Description
The ORTNER is a
revolutionary concept for dewatering, removing fines, classifying and
rinsing sand and other materials up to
2 inches. The ORTNER has the performance capabilities and advantages
unmatched by other machinery.
Ortner can wash fine and course
material up to 3 inches. The flexibility of The ORTNER®
enables you to produce many varied products with one machine.
Dry material may be fed to the ORTNER® to remove excess fines or rinse coarse material by adding a small quantity of water.
When fed a wet slurry, as from a density separator or a hydrocyclone, the ORTNER® may be used to dewater the product. The ORTNER® may be used to remove excess fines from the slurry or it may classify the slurry.
Go Back To Top
Operation
The operation and principle are simple. Material is fed to a slowly revolving pan on an incline and vibrated at high speed. The high speed vibration quickly separates the various sizes of material with the fines and water rising to the top and flowing over the pan's edge to the discharge. The coarser particles sink to the bottom. The rotating pan carries the settled particles up the machine and out of the water, where a stationary plow diverts the dewatered material to a center discharge spout.
The driving and vibrating mechanism is mounted under the pan, preventing any contamination with the water and processed material, thus increasing the life of the components.
It is possible to vary the angle, speed, and vibrations of the pan. This gives the ORTNER® a wide range of flexibility and increases its capacity and efficiency.
Pennsylvania manufactured sand operator
removing excess fines.
Go Back To Top
Design
Features
DRIER
PRODUCT. High efficiency produces dry product for ease of conveying and stockpiling.
LESS
POWER. Horsepower requirements range from 2-15 HP depending on model. Normally one-fifth the power consumption of conventional machines.
HIGH
CAPACITY. Unmatched performance capabilities and flexibility.
LESS WATER. A relatively small amount of water is needed to rinse and remove excess fines.
LESS
WEAR. Lowest wear and maintenance cost results from simple design.
LESS WEIGHT. Compact and lightweight for portability and easy installation.
Go Back To Top
Ortner®
Selection and Tests
The proper ORTNER® application and sizing must take into consideration the type of material, feed gradations, product specifications, water in feed and availability, tonnage required and feed particle shape. Aggregates Equipment, Inc. has testing facilities to assure proper ORTNER® selection and applications. Aggregates Equipment, Inc. will be pleased to test and make recommendations.
Go Back To Top
Ortner®
Capacity Charts
To view the drawing
above larger, click on the drawing (The
file is approximately 19k in size and may take longer to download).
The page of drawings
that loads is used in conjunction with the tables below to determine
dimensions and capacities of the ORTNER®
for your specific needs.
| Dimensions -
in inches. All models available as portable units |
| MODEL |
A |
B |
C |
D |
E |
F |
G |
H |
J |
K |
L |
M |
| 2000 |
79 |
67 |
90 |
103 |
70 |
67 |
33 |
28 |
2 |
9 |
33 |
73 |
| 2500 |
99 |
83 |
110 |
138 |
98 |
95 |
40 |
41 |
3 |
11 |
35 |
106 |
| 3000 |
118 |
79 |
130 |
151 |
98 |
95 |
53 |
43 |
5 |
11 |
35 |
105 |
| 3500 |
138 |
89 |
152 |
179 |
115 |
111 |
64 |
49 |
4 |
12 |
37 |
116 |
| 4000 |
158 |
94 |
172 |
194 |
131 |
126 |
63 |
58 |
6 |
14 |
42 |
125 |
| Capacities |
| MODEL |
*CAPACITY (TPH) |
HP |
LBS. WEIGHT |
| 2000 |
10-30 |
2 |
5,000 |
| 2500 |
30-70 |
5 |
9,000 |
| 3000 |
50-125 |
5 |
10,000 |
| 3500 |
80-170 |
10 |
14,000 |
| 4000 |
120-210 |
15 |
18,000 |
*Capacities
are approximate for concrete sand and will vary depending on
size and type of material, moisture content of feed,
specifications and water
availability. Contact factory for evaluations and recommendations
of your
particular requirements.
Go Back To Top
|
